technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland. 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com pnp silicon switching transistor qualified per mil-prf-19500/512 t4-lds-0157 rev. 2 (101305) page 1 of 6 devices levels 2n4029 2n4033 jan 2N4033UA jantx 2n4033ub jantxv jans absolute maximum ratings (t c = +25c unless otherwise noted) parameters / test conditions symbol value unit collector-emitter voltage v ceo 80 vdc collector-base voltage v cbo 80 vdc emitter-base voltage v ebo 5.0 vdc collector current i c 1.0 adc total power dissipation @ t a = +25c 2n4029 1 2n4033 2 2N4033UA, ub 3 p t 0.5 0.8 0.5 w operating & storage junction temperature range t j , t stg -65 to +200 c thermal resistance, junction-to-case 2n4029 2n4033 r jc 80 40 c/w note: 1. derate linearly 2.86mw/c for t a > +25c 2. derate linearly 4.56mw/c for t a > +25c 3. for ub package and use r jc or see thermal curves in /512 electrical characteristics (t a = +25c, unless otherwise noted) parameters / test conditions symbol min. max. unit off charactertics collector-base cutoff current v cb = 80vdc v cb = 60vdc v cb = 60vdc, t a = +150c i cbo 10 10 25 adc adc adc emitter-base cutoff current v eb = 5.0vdc v eb = 3.0vdc i ebo 10 25 adc adc collector-emitter cutoff current v be = 2.0vdc, v ce = 60vdc i cex 25 adc to-18 (to-206aa) 2n4029 to-39 (to-205ad) 2n4033 ua package ub package
technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland. 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com t4-lds-0157 rev. 2 (101305) page 2 of 6 electrical characteristics (t a = +25c, unless otherwise noted) parameters / test conditions symbol min. max. unit on characteristics (3) forward-current transfer ratio h fe i c = 100 adc, v ce = 5.0vdc 50 i c = 100madc, v ce = 5.0vdc 100 300 i c = 500madc, v ce = 5.0vdc 70 i c = 1.0adc, v ce = 5.0vdc 25 i c = 500madc, v ce = 5.0vdc, t a = -55c 30 collector-emitter saturation voltage v ce(sat) vdc i c = 150madc, i b = 15madc i c = 500madc, i b = 50madc i c = 1.0adc, i b = 100madc 0.15 0.50 1.0 base-emitter voltage v be(sat) vdc i c = 150madc, i b = 15madc i c = 500madc, i b = 50madc 0.9 1.2 dynamic characteristics parameters / test conditions symbol min. max. unit magnitude of common emitter small?signal short-circuit forward current transfer ratio |h fe | i c = 50madc, v ce = 10vdc, f = 100mhz 1.5 6.0 output capacitance c obo 20 pf v cb = 10vdc, i e = 0, 100khz f 1.0mhz input capacitance c ibo 80 pf v eb = 0.5vdc, i c = 0, 100khz f 1.0mhz switching characteristics parameters / test conditions symbol min. max. unit on-time v cc = 31.9vdc; i c = 500madc; i b1 = 50madc t d 15 s rise time v cc = 31.9vdc; i c = 500madc; i b1 = 50madc t r 25 s storage time v cc = 31.9v, i c = 500madc, i b1 = 50madc t s 175 s fall time v cc = 31.9v, i c = 500madc, i b1 = 50madc t f 35 s (4) pulse test: pulse width = 300 s, duty cycle 2.0%.
technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland. 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com t4-lds-0157 rev. 2 (101305) page 3 of 6 package dimensions notes: 1 dimension are in inches. 2 millimeters equivalents are given for general information only. 3 beyond r (radius) maximum, tw shall be held for a minimum length of .011 (0.28 mm). 4 dimension tl measured from maximum hd. 5 body contour optional within zone defined by hd, cd, and q. 6 leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18mm) radius of true position (tp) at maximum material condition ( mmc) relative to tab at mmc. the device may be measured by direct methods. 7 dimension lu applies between l 1 and l 2 . dimension ld applies between l 2 and minimum. diameter is uncontrolled in l 1 and beyond ll minimum. 8 all three leads. 9 the collector shall be internally connected to the case. 10 dimension r (radius) applies to both inside corners of tab. 11 in accordance with asme y14.5m , diameters are equivalent to x symbology. 12 for ?l? suffix devices, dimension ll is 1.50 (38.10mm) minimum, 1.75 (44.45mm) maximum. figure 1. physical dimensions for 2n4029 (to-18) . dimensions symbol inches millimeters notes min max min max cd .178 .195 4.52 4.95 ch .170 .210 4.32 5.34 hd .209 .230 5.31 5.84 lc .100 tp 2.54 tp 6 ld .016 .021 0.41 0.53 7, 8 ll .500 .750 12.70 19.05 7, 8, 12 lu .016 .019 0.41 0.48 7, 8 l 1 .050 1.27 7, 8 l 2 .250 6.35 7, 8 q .040 1.02 5 tl .028 .048 0.71 1.22 3, 4 tw .036 .046 0.91 1.17 3 r .010 0.25 10 p .100 2.54 45 tp 6
technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland. 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com t4-lds-0157 rev. 2 (101305) page 4 of 6 notes: 1 dimension are in inches. 2 millimeters equivalents are given for general information only. 3 beyond r (radius) maximum, tw shall be held for a minimum length of .011 (0.28 mm). 4 dimension tl measured from maximum hd. 5 body contour optional within zone defined by hd, cd, and q. 6 leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18mm) radius of true position (tp) at maximum material condition ( mmc) relative to tab at mmc. the device may be measured by direct methods. 7 dimension lu applies between l 1 and l 2 . dimension ld applies between l 2 and minimum. diameter is uncontrolled in l 1 and beyond ll minimum. 8 all three leads. 9 the collector shall be internally connected to the case. 10 dimension r (radius) applies to both inside corners of tab. 11 in accordance with asme y14.5m , diameters are equivalent to x symbology. 12 for ?l? suffix devices, dimension ll is 1.50 (38.10mm) minimum, 1.75 (44.45mm) maximum. figure 2. physical dimensions for 2n4033 (to-39) . dimensions symbol inches millimeters notes min max min max cd .305 .335 7.75 8.51 ch .240 .260 6.10 6.60 hd .335 .370 8.51 9.40 lc .200 tp 5.08 tp 6 ld .016 .021 0.41 0.53 7, 8 ll .500 .750 12.70 19.05 7, 8, 12 lu .016 .019 0.41 0.48 7, 8 l 1 .050 1.27 7, 8 l 2 .250 6.35 7, 8 q .050 1.27 5 tl .029 .045 0.74 1.14 3, 4 tw .028 .034 0.71 0.86 3 r .010 0.25 10 p .100 2.54 45 tp 6
technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland. 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com t4-lds-0157 rev. 2 (101305) page 5 of 6 dimensions dimensions ltr. inches millimeters note lt r. inches millimeters note min max min max min max min max a .061 .075 1.55 1.91 3 d 2 .0375 bsc 0.952 bsc a 1 .029 .041 0.74 1.04 d 3 .155 3.94 b 1 .022 .028 0.56 0.71 e .215 .225 5.46 5.72 b 2 .075 ref 1.91 ref e 3 .225 5.72 b 3 .006 .022 0.15 0.56 5 l 1 .032 .048 0.81 1.22 d .145 .155 3.68 3.93 l 2 .072 .088 1.83 2.24 d 1 .045 .055 1.14 1.39 l 3 .003 .007 0.08 0.18 5 notes: 1 dimensions are in inches. 2 millimeters equivalents are given for general information only. 3 dimension ?a? controls the overall pack age thickness. when a window lid is us ed, dimension ?a? must increase by a minimum of .010 inch (0.254 mm) and a maximum of .040 inch (1.020 mm). 4 the corner shape (square, notch, radius , etc) may vary at the manufacturer?s op tion, from that shown on the drawing. 5 dimensions ?b3? minimum and ?l3? minimum and the appropriately castellation length define an unobstructed three- dimensional space traversing all of the ceramic layers in whic h a castellation was designed. (castellations are required on bottom two layers, optional on top ceramic layer.) dimensi on ?b3? maximum and ?l3? maximum define the maximum width and depth of the castellation at any point on its surface. measurement of these dimensi ons may be made prior to solder dipping . 6 in accordance with asme y14.5m , diameters are equivalent to x symbology. figure 3. physical dimensions, surface mount (ua version) .
technical data sheet 6 lake street, lawrence, ma 01841 gort road business park, ennis, co. clare, ireland. 1-800-446-1158 / (978) 620-2600 / fax: (978) 689-0803 tel: +353 (0) 65 6840044 fax: +353 (0) 65 6822298 website: http://www.microsemi.com t4-lds-0157 rev. 2 (101305) page 6 of 6 notes: 1 dimensions are in inches. 2 millimeters are given for general information only. 3 hatched areas on package denote metalized areas. 4 pad 1 = base, pad 2 = emitter, pad 3 = collector, pad 4 = shielding connected to the lid. 5 in accordance with asme y14.5m , diameters are equivalent to x symbology. figure 4. physical dimensions, surface mount (ub version) . dimensions symbol inches millimeters note min max min max bh .046 .056 1.17 1.42 bl .115 .128 2.92 3.25 bw .085 .108 2.16 2.74 cl .128 3.25 cw .108 2.74 ll1 .022 .038 0.56 0.96 ll2 .017 .035 0.43 0.89 dimensions symbol inches millimeters note min max min max ls1 .036 .040 0.91 1.02 ls2 .071 .079 1.81 2.01 lw .016 .024 0.41 0.61 r .008 .203 r1 .012 .305 r2 .022 .559
|
